NO wobble , JUST bushings
+3
Badmoon
Steve-O
horseman8m
7 posters
Page 1 of 1
NO wobble , JUST bushings
This is to pass on to everyone that even though i didn't have a wobble i changed my shock bushings with the "MCMasters" nylon bushing they were easy to change out , jacked up , one side at a time , 12mm wrench , easy to get off and a flick with the screwdriver removed the old rubber bushings and a "C" clamp installed the new ones . to put the shocks back on i used the top bolt on the bottom and slowly pressed the bushing & lower shock into place at the same time i used a rubber hammer to press the top of the shock in then when the bottom was close then removed the top bolt from the bottom and installed both bolts in the right place and tightened them . then repeated for the other side. it rides better now, I even turned down the shocks a notch for a better ride.
I found out some facts for you , rubber bushings have a crush pressure of 750 pounds per sq in.
High density polyethylene "HDPE" bushings have a crush pressure of 1,200 pounds per sq in.
Nylon bushings have a crush pressure of 16,000 pounds per sq in.
I went with the Nylon bushings.
good luck,
Horse
I found out some facts for you , rubber bushings have a crush pressure of 750 pounds per sq in.
High density polyethylene "HDPE" bushings have a crush pressure of 1,200 pounds per sq in.
Nylon bushings have a crush pressure of 16,000 pounds per sq in.
I went with the Nylon bushings.
good luck,
Horse
horseman8m- Number of posts : 1449
Age : 36
Location : valdosta , GA.
Registration date : 2008-02-09
Re: NO wobble , JUST bushings
Good info! Thanks!
Steve-O- Moderate user
- Number of posts : 1153
Age : 65
Location : Dallas, TX
Registration date : 2008-02-05
Re: NO wobble , JUST bushings
That is some good information, Thanks
Can the tire withstand 16,000 lbs? Dang boy how big are ya?
Just messin.
Moon
Can the tire withstand 16,000 lbs? Dang boy how big are ya?
Just messin.
Moon
Badmoon- Number of posts : 1699
Age : 57
Location : Swanpland (Gods Country) It is my horns that hold up my halo.
Registration date : 2007-12-20
Re: NO wobble , JUST bushings
I went with the nylons a couple years ago...they look brand new!
....................bobby
.
....................bobby
.
twin1300- Admin
- Number of posts : 4689
Age : 64
Location : Denham Springs, La.
Registration date : 2007-12-14
Re: NO wobble , JUST bushings
Where do you get them?
jnv753- Number of posts : 20
Location : Belen, NM
Registration date : 2008-03-27
Re: NO wobble , JUST bushings
P/N 6389K344
Nylon Bearing Sleeve, for 5/8" Shaft Dia, 7/8" OD, 3/4" Length, Packs of 5
$4.22 for a pack of 5
http://www.mcmaster.com/nav/enter.asp?partnum=6389K344&pagenum=1070
Jerry
Nylon Bearing Sleeve, for 5/8" Shaft Dia, 7/8" OD, 3/4" Length, Packs of 5
$4.22 for a pack of 5
http://www.mcmaster.com/nav/enter.asp?partnum=6389K344&pagenum=1070
Jerry
jedishon- Super User
- Number of posts : 4436
Age : 73
Location : Rogersville, Al
Registration date : 2007-12-18
Re: NO wobble , JUST bushings
But what do you do with the extra one??
George
George
gstanfield- Super User
- Number of posts : 583
Age : 45
Location : Rolling Hills, WY
Registration date : 2007-12-15
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum